A Plan of materials irradiation facility at J-PARC for development of ADS and high-power accelerator facilities

Maekawa, Fujio

JPS Conference Proceedings (Internet), 33, p.011042_1 - 011042_6, 2021/03

https://doi.org/10.7566/JPSCP.33.011042

Development of beam window (BW) materials is one of crucial issues in development of accelerator driven nuclear transmutation systems (ADS). The BW is exposed to high energy protons and spallation neutrons, and also to corrosive lead-bismuth eutectic (LBE) alloy at high temperature of about 500C. Recently, not only high-power accelerators but also high-power targets are the rate-limiting factor for increasing the power of accelerator facilities in terms of radiation damage and heat removal. To study radiation damage on BW and target materials for high-power accelerator facilities including ADS, we are planning a materials irradiation facility by utilizing the proton beam of 400 MeV and 250 kW provided by the J-PARC's Linac. The target is flowing LBE alloy which is a candidate target and coolant material of ADS. When a steel sample is irradiated in the target for one year, the sample receives radiation damage of about 10 dpa at maximum which is equivalent to the yearly radiation damage of ADS's BW. In the current facility concept, the facility is equipped with a hot-laboratory for efficient post-irradiation examination. The facility will be outlined in this presentation.

Impact of PHITS spallation models on the neutronics design of an accelerator-driven system

Iwamoto, Hiroki; Nishihara, Kenji; Iwamoto, Yosuke; Hashimoto, Shintaro; Matsuda, Norihiro; Sato, Tatsuhiko; Harada, Masahide; Maekawa, Fujio

Journal of Nuclear Science and Technology, 53(10), p.1585 - 1594, 2016/10

https://doi.org/10.1080/00223131.2016.1140598

Measurement of LBE flow velocity profile by UDVP

Kikuchi, Kenji; Takeda, Yasushi*; Obayashi, Hiroo*; Tezuka, Masao*; Sato, Hiroshi

Journal of Nuclear Materials, 356(1-3), p.273 - 279, 2006/09

https://doi.org/10.1016/j.jnucmat.2006.05.028

Measurements of LBE flow velocity profile were realized in the spallation target model by the ultrasonic Doppler velocity profile technique. Hitherto, it has not yet been done well because both of poor wetting property of LBE with stainless steels and poor performance of supersonic probes at high temperatures. Measurement was made for a return flow in the target model, which has coaxially arranged annular and tube channels. The electromagnetic pump generates LBE flow and the flow rate was measured by the electromagnetic flow meter. Measurement results show that re-circulation occurred near the surface of beam window, which might affect a heat transfer of target container.

Development of reliable diamond window for EC launcher on fusion reactors

Takahashi, Koji; Illy, S.*; Heidinger, R.*; Kasugai, Atsushi; Minami, Ryutaro; Sakamoto, Keishi; Thumm, M.*; Imai, Tsuyoshi

Fusion Engineering and Design, 74(1-4), p.305 - 310, 2005/11

https://doi.org/10.1016/j.fusengdes.2005.06.234

A new diamond window with the copper-coated edge for an EC launcher is developed. The diamond window is designed to cool its disk edge. Since Cu is coated at the entire edge, ingress of cooling water into a transmission line in case of failure on the edge is negligible. In addition, corrosion of Al blaze between the edge and the Inconel cuffs can be avoided. A 170GHz, RF transmission experiment equivalent to a MW-level transmission was carried out to investigate the capability of the edge cooling. The transmission power and pulse are 55kW and 3sec, respectively. Temperature increase was 45C and alomost became constant. Thermal calculation with tan of 4.410 and thermal conductivity of 1.9kW/m/K agrees with the experiment. Since tan of the diamond is much higher than the actual one (tan=210), the temperature increase corresponds to that of 1MW transmission. It concludes that the Cu coating dose not degrade the edge cooling capability and improves the reliability of the diamond window.

Design study around beam window of ADS

Oigawa, Hiroyuki; Tsujimoto, Kazufumi; Kikuchi, Kenji; Kurata, Yuji; Sasa, Toshinobu; Umeno, Makoto*; Nishihara, Kenji; Saito, Shigeru; Mizumoto, Motoharu; Takano, Hideki*; et al.

Proceedings of 4th International Workshop on the Utilisation and Reliability of High Power Proton Accelerators, p.325 - 334, 2005/11

The Japan Atomic Energy Research Institute (JAERI) is conducting the research and development (R&D) on the Accelerator-Driven Subcritical System (ADS) for the effective transmutation of minor actinides (MAs). The ADS proposed by JAERI is the 800 MWth, Pb-Bi cooled, tank-type subcritical reactor loaded with (MA+Pu) nitride fuel. The Pb-Bi is also used as the spallation target. In this study, the feasibility of the ADS was discussed with putting the focus on the design around the beam window. The partition wall was placed between the target region and the ductless-type fuel assemblies to keep the good cooling performance for the hot-spot fuel pin. The flow control nozzle was installed to cool the beam window effectively. The thermal-hydraulic analysis showed that the maximum temperature at the outer surface of the beam window could be repressed below 500 C even in the case of the maximum beam power of 30 MW. The stress caused by the external pressure and the temperature distribution of the beam window was also below the allowable limit.

Effect of proton beam profile on stress in JSNS target vessel

Kogawa, Hiroyuki; Ishikura, Shuichi*; Sato, Hiroshi; Harada, Masahide; Takatama, Shunichi*; Futakawa, Masatoshi; Haga, Katsuhiro; Hino, Ryutaro; Meigo, Shinichiro; Maekawa, Fujio; et al.

Journal of Nuclear Materials, 343(1-3), p.178 - 183, 2005/08

https://doi.org/10.1016/j.jnucmat.2004.08.032

A cross-flow type (CFT) mercury target with flow guide blades, which has been developed for JSNS, can suppress the generation of stagnant flow region especially near the beam window where the peak heat density is generated due to spallation reaction. Then, a flat type beam window has been applied to the CFT target from the viewpoint of suppressing dynamic stress caused by a pressure wave, which has been estimated with a mercury model of the linear equation of state. The recent experimental results obtained by using a proton beam incidents to mercury led that a cutoff pressure model in the equation of state of mercury caused a suitable dynamic stress with experimental results. Dynamic stress analyses were carried out with the cutoff pressure model, in which the negative pressure less than 0.15 MPa was not generated. The generated dynamic stress in the flat beam window became much larger than that in a semi-cylindrical type window. However, the generated stress in the semi-cylindrical type beam window was over the allowable stress of SS316L under the peak heat density of 668 W/cc. In order to decrease the dynamic stress in the semi-cylindrical beam window, the incident proton beam was defocused to decrease the peak heat density down to 218 W/cm. As a result, the dynamic stress could be suppressed less than the allowable stress. On the other hand, due to defocus of the proton beam, high heat density was generated on the end of the flow guide blades, which caused high thermal stress exceeding the allowable stress. To decrease the thermal stress, several shapes of the blade ends were studied analytically, which were selected so as not to affect the mercury flow distribution. A simple thin-end blade showed low thermal stress below the allowable stress.

Development of EC launcher components for ITER

Takahashi, Koji; Kobayashi, Noriyuki*; Kasugai, Atsushi; Sakamoto, Keishi

Journal of Physics; Conference Series, 25, p.75 - 83, 2005/00

https://doi.org/10.1088/1742-6596/25/1/010

Recent progress of the development on the ITER equatorial EC launcher components, such as the steering mirrors, its drive system, the waveguide components and the diamond vacuum windows, is reported. Thermmo-mechanical analysis of the recent mirror design shows that maximum temperature increase of 187C at the reflecting surface and maximum stress of 242MPa at the inner surface of the cooling tube are obtained. In the cyclic test of the spiral tube mock-up, the cyclic number of 1.310 is succeeded without failure. In the window development, the fabrication of the Cu-coated edge diamond window and the high power transmission test were done. The Cu-coating on the disk edge can avoid water ingress in the launcher (vessel) under the assumption of the crack formation toward edge. Transmission experiment indicative to 1.2MW, was carried out. Temperature increase of 50C agrees with the calculation. It concludes that the Cu-coated window is capable of MW-level transmission and improves its reliability.

Application of diamond window for infrared laser diagnostics in a tokamak device

Kawano, Yasunori; Chiba, Shinichi; Inoue, Akira*

Review of Scientific Instruments, 75(1), p.279 - 280, 2004/01

https://doi.org/10.1063/1.1633990

It has been successful to apply CVD diamond plate as the vacuum window for infrared CO laser interferometry and polarimetry for electron density measurement in the JT-60U tokamak. In comparison with to use the conventional zinc-selenide windows, the Faraday rotation component at diamond windows was small as negligible. This resulted in the improvement of the Faraday rotation measurement for a tokamak plasma by polarimetry.

Design of beam incident monitor for spallation neutron target of JSNS

Meigo, Shinichiro; Harada, Masahide; Teraoku, Takuji*; Maekawa, Fujio

Proceedings of ICANS-XVI, Volume 3, p.1175 - 1180, 2003/07

It is important to monitor the proton beam for the high intensity pulse spallation target. Especially for the beam halo, which may irradiate the bulk surrounding the target, it is important to be observed to prevent causing heat spot in the shielding bulk. At JSNS, a proton beam monitors are located at front of the target. These monitors are assembled with the proton beam window. Since this scheme increases the radiation on the monitor due to the beam loss at the windows, it may arise heat deposition on the monitor. Therefore, heat deposition is calculated with NMTC/JAM. It is found that the heat deposition for normal operation is less than 0.1 W/cc.

Structual design study of a proton beam window for a 1-MW spallation neutron source

Teraoku, Takuji*; Terada, Atsuhiko*; Maekawa, Fujio; Meigo, Shinichiro; Kaminaga, Masanori; Ishikura, Shuichi*; Hino, Ryutaro

JAERI-Tech 2003-026, 77 Pages, 2003/03

JAERI-Tech-2003-026.pdf:19.78MB

A 1-MW spallation neutron source aiming at materials and life science researches will be constructed under the JAERI-KEK Proton Accelerator Project(J-PARC). The proton beam window functions as a boundary wall between a high vacuum area and a helium atmosphere and it is cooled by light water because high heat-density is generated in the window material by interactions with the proton beam. Then, uniformity of the water flow is requested at the window to suppress a hot-spot that causes excessive thermal stress and cooling water boiling. Also, the window has to be strong enough in its structure for inner stress due to water pressure and thermal stress due to heat generation. In this report, we propose two types of proton beam windows, flat-type and curved-type. We evaluated the strength of structure and thermal hydraulic analysis. As a result, it was found that sufficient heat removal was assured with uniform water flow at the window, and the stress could be maintained below allowable stress values. Accordingly, it was confirmed that the proton beam window designs were feasible.